2THEMAX MR740S USB-IRDA DONGLE WINDOWS 10 DOWNLOAD DRIVER
2THEMAX MR740S USB-IRDA DONGLE DRIVER DETAILS:
|File Size:||8.8 MB|
|Supported systems:||Windows 2K, Windows XP, Windows Vista, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10|
|Price:||Free* (*Free Registration Required)|
2THEMAX MR740S USB-IRDA DONGLE DRIVER
For CTs with terminals, there should be a label on the HI terminal.
There are many symptoms you may see if the CTs are installed correctly. Mostly you will see things like negative watts in the Power readings. You may also see a reversal in the Energy Delivered and Energy Received registers. We can often look at the Phasor diagram and diagnose this issue. If you think you may have an issue send a phasor diagram to support electroind. We also need to know if you are connected as a Wye or Delta. Current and Voltage values will be normal since they only represent absolute values. 2TheMax MR740S USB-IrDA Dongle
If you have one CT oriented wrong, things like Total Energy will be in error because the energy in one phase will be subtracted from the energy in the other two phases. Primarily there are two critical things to get correct.
First is the orientation of the CT. All CTs have a marking like a white dot on one side.
This should always be installed facing the power source. For a typical installation on a building or where you want to measure energy to a load, you want the white dot facing the utility company. You should always use a shorting block for your CTs unless you are working with a system that can easily 2TheMax MR740S USB-IrDA Dongle powered down for maintenance. The outputs of a CT should always be shorted together when the system is energized. If current is not allowed to flow the CTs will heat up very quickly and be damaged.
Shorting blocks allow you to change out a meter without shutting down the system and will protect the CTs from being 2TheMax MR740S USB-IrDA Dongle. With the Nexus meters we mostly provide readings in secondary values. There are 2 ways to get to the primary values. Shark meters are ideal for getting the energy readings for loads, generation and even mixed systems that generate part of the time and act like a load part of the time. A good example of the latter is a wind farm. When the wind is not blowing or the propeller is stopped, 2TheMax MR740S USB-IrDA Dongle wind generator will actually use energy to keep its transmission warm on cold days.
IrDA, IR Products
For systems that have both, one value will show up as negative watt hours. The NET would be the sum of the two and this would be the energy that the power company would need to pay the wind farm for. 2TheMax MR740S USB-IrDA Dongle
Download the driver from this link: This is the default modbus password. From the Shark Modbus Register Map, the Primary Readings Block Format is Float or reverse float for most software settings but for some software that doesnt have the Float format, Integer reads can be used by using the formula. The default configuration works only with initial meter device profile.
This means the PT numerator and denominator 2TheMax MR740S USB-IrDA Dongle CT num are not changed. Programming will need our Communicator EXT 3. The assumption for the Kh is correct. So, the overall factor to be used to multiplied to the number of pulses counted by the PLC is. The phase A reading is your Max Demand Watts reading or Peak demand at 15 minute interval default settings. The dongle comes already with Windows 7 compatible driver and so driver installation is automatic. Yes the meter can be used for any single phase application 2 wire or 3 wire.
The manual already have an example of the wiring diagram for Dual phase 3 wire and single phase 2 wire. This page contains information about installing the 2TheMax MR740S USB-IrDA Dongle 2TheMax MRS USB-IrDA Dongle driver downloads using the 2TheMax Driver Update Tool. 2TheMax MRS USB-IrDA Dongle Free Driver Download for Windows - . World's most popular driver download site.